PORSCHE 930 MOUNTING PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 GT3 2007-11 - Body (includes uncategorized and accessory items) FVD10699710 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$526.90
Make a selection 846R9003 Material: tig welded, type 304, stainless steel. Finish: satin finish stainless. Weight: 6oz. Models: 996/997, Boxster, 911 & 944. Installation: secures snap-in lap belts to outside seat belt mounting point. Miscellaneous: allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Use part 846r-9001 for inside belt mount.
$112.20
Make a selection 91150301605KEV Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar headlight bucket. Features: - produced by an OEM manufacturer. - lightweight .6 lbs. (.3 kg) - made of high strength kevlar. - metal mounting ring is cast inside the bucket for mounting. Sold individually. 1 necessary per car. Please note: requires drilling for wiring, etc. This is a high-quality part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$774.40
Make a selection 91150301505KEV Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar headlight bucket. Features: - produced by an OEM manufacturer. - lightweight .6 lbs. (.3 kg) - made of high strength kevlar. - metal mounting ring is cast inside the bucket for mounting. Sold individually. 1 necessary per car. Please note: requires drilling for wiring, etc. This is a high-quality part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$774.40
Make a selection 846R1030 The harness mount bar has been tested and certified by an independent lab to handle the types of forces required by the national highway traffic safety admin. Dot and sae j385 rev. Mar 95, motor vehicle seat belt anchorages-performance requirements. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$710.20
Make a selection FVDBSK351993002 Make your next service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Front right rotor (zimmermann formula z) 1 qty. Front left rotor (zimmermann formula z) 1 qty. Oem set of front pads (4 total) 2 qty. Oem brake warning sensors 4 qty. Oem brake pad damping plates (for 44 mm piston) 4 qty. Oem brake pad damping plates (for 36 mm piston) 2 qty. Oem brake caliper mounting bolts - m12x72mm sold as a kit. 1 necessary per car.
$943.80
Make a selection HEI911002001S1 We deliver with dmsb-ons certificat ,incl. Tunneling supporting and diagonal bars for the work location motorsport you need this options: 600001 side rotection 600035 dash board panel faces optional : 600036 harness mounting tube only in steel 600006 upholstery 600014 diagonals bars with connecting joint every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated.
$2,406.80
Make a selection HEI964001002S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We r...(choose a part on the right to read more)
$686.40
Make a selection HEI997001006S Standart black - optinal color optional : 600036 harness mounting tube only in steel 600006 upholstery 2x every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated. General Fitment911 GT3 2007-11911 2009-12 911 2005-08
From $1,675.18
Make a selection HEI997001002S Optional : 600036 harness mounting tube only in steel 600006 upholstery 2x every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated. General Fitment911 GT3 2007-11911 2009-12 911 2005-08
From $1,155.47
Make a selection 113LM099FD Genuine bbs motorsport center cap finished in gloss black with a silver logo. This cap is used primarily on the bbs rs, rx, rm and le mans type 099 wheel.
$22.00
Make a selection 097121600009 The techart program is exclusively developed by their designers, engineers, technicians and model builders. Working closely together, the team designs, builds prototypes and tests the parts in the wind tunnel until each item is approved for road-legal use and launched for the worldwide market. Every component is manufactured from select materials to exacting quality norms. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08
From $1,117.60
Make a selection
From $55.00
Make a selection BBI9818200001 Bbi autosport Porsche 981 Cayman GT4 streetcup roll bar features 4130 chrome moly steel tubing for excellent strength to weight ratio and addresses issues such as harness angle, seat travel, and engine compartment access. Taking a sensible design approach, the bar mounts to frame structure in the cabin and rear strut towers to provide the strongest mounting points and maximum protection. For superior strength and rigidity, high strength 4130 chrome moly steel tubing was used throughout and all joints are meticulously tig welded by hand. Bolt-in installation is accomplished by using inner diameter tube clamps that are cnc turned and milled for a precise fit. These unique joints eliminate the unsightly through-bo...(choose a part on the right to read more)
$2,395.00
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection BES99107060S The perfect addition for an aggressive exhaust note with the added benefit of reduced weight. Features: 2 1/2 (63.5mm) tubing. Weighs 8.3 lbs. (3,7 kg), 10 + lbs. Savings over stock GT3 center muffler. Made of German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Fits 991.1 and 991.2 GT3 & GT3 rs models.- reuse's factory tips. Includes all necessary clamps and mounting brackets. Made in Germany by m&m exhaust, gmbh. Intoxicating growl at idle, partial throttle and wide-open throttle. No interior resonance or drone. Ecu software is not necessary. Does not alter emissions, 50 state legal in the u.s. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. T...(choose a part on the right to read more)
$2,313.30
Make a selection 96437504381UNI The rs model engine mount is not a hydro-elastic mount like most models. It contains a rubber core with an 85-shore hardness value. That equates to a more responsive chassis and improved shifting response. A perfect compromise for street and track use as it is more forgiving than aftermarket solid mounts. Sold individually. 2 necessary per car. To install these mounts on any model 964 / 965 / 993 and 993 tt, we recommend our rs engine mount set that includes 2 mounts and all the mounting hardware, part # FVD375964
$218.90
Make a selection 91163193301EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's and passenger's side fitment. 2 necessary per car.
$93.50
Make a selection 097100600009 The techart program is exclusively developed by their designers, engineers, technicians and model builders. Working closely together, the team designs, builds prototypes and tests the parts in the wind tunnel until each item is approved for road-legal use and launched for the worldwide market. Every component is manufactured from select materials to exacting quality norms. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08
From $522.50
Make a selection 270503055 High-quality OEM front chin spoiler kit replacement that includes all necessary installation hardware. We source this part in Germany to ensure quality, reliability and precise fitment. Kit includes: qty. 1 front chin spoiler 930 / 911 wide body / turbo look 1975-89 - 93050305501 qty. 11 spoiler shim - 91150302300 qty. 1 left spoiler mounting plate qty. 1 right spoiler mounting plate qty. 15 m6 stainless nuts qty. 15 m6 washers sold individually. 1 needed per car.
$2,001.90
Make a selection 91163193300EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's or passenger's side fitment. 2 necessary per car.
$93.50
Make a selection FVDBSK351997006 Brake service kit contains: - brake discs - brake pads - caliper screws - warning contacts - damping plates - mounting parts everything you need to service your front brake complete.
$504.90
Make a selection 846R9001R01 Material: tig welded, type 304, stainless steel. Finish: satin finish stainless. Weight: 6oz. Models: 996/997, Boxster, 911 & 944. Installation: secures snap-in lap belts to factory tunnel side (inside) seat belt mounting point. Miscellaneous: allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Note: part# 846 r9002 hardware kit is required for installation in (1985 - 1989) model Porsches. Use part 846 r9003 for outside belt mount.
$69.30
Make a selection FVD802001 This is an ideal way to update your early model Porsche to a central locking system that locks both doors with the turn of the key. The kit is complete with 2 actuators, control module, mounting hardware, proper cabling, installation and operating instructions. We recommend pairing this kit with the radio remote control, part # FVD8020011 sold as a kit. 1 necessary per car.
$190.00
Make a selection BES99725060SR Brombacher sport muffler for 997.2 GT3 / rs (sound version) with rsr style tips facts: - + 10 crank hp & + 10 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 28 lbs. (12.7 kg) - replaces stock side mufflers and stock center muffler - 36 lbs (16.3 kg) savings over stock system! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - 2 x 3.5 (90mm) rsr angle cut tips - includes all necessary clamps and mounting brackets - made in Germany - 105 db - intoxicating cup car growl at idle, partial throttle and wide open throttle - no interior resonance - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. For reference: 997 GT3 OEM ...(choose a part on the right to read more)
$3,023.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |